330MW汽轮机单多阀切换时轴承振动原因分析

华电技术 ›› 2011, Vol. 33 ›› Issue (2): 6-7.

330MW汽轮机单多阀切换时轴承振动原因分析

曾琦

华电新疆发电有限公司乌鲁木齐热电厂，新疆乌鲁木齐830017

收稿日期:1900-01-01 修回日期:1900-01-01 出版日期:2011-02-25 发布日期:2011-02-25

Analysis on reasons of bearing vibration of 330MW steam turbine in changeover from single valve mode into sequence valve mode

ZENG Qi

Urumqi Thermal Power Plant of Huadian Xinjiang Power Generation Corporation Limited ，Urumqi 830017, China

Received:1900-01-01 Revised:1900-01-01 Online:2011-02-25 Published:2011-02-25

摘要/Abstract

摘要： 华电新疆发电有限公司乌鲁木齐热电厂 #1汽轮机在单多阀切换后，汽轮机 #1轴承X，Y向振动增大到接近200μm，严重影响了机组的安全性，只有重新切回单阀状态运行。单阀运行状态机组截流损失较大，增大机组的汽耗，降低了机组经济性，采取了调整机组单多阀开启顺序的方法，使机组振动控制在70μm以下，达到了预期的效果。

关键词: 单阀运行, 振动, 原因分析, 单多阀开启顺序

Abstract: In Urumqi Thermal Power Plant of Huadian Xinjiang Power Generation Corporation Limited, after the operation mode of steam turbine No.1 was changed over from single valve mode into sequence valve mode, the bearing vibration of turbine No.1 in X,Y direction increased to about 200μm, which has a strong impact on unit safety; so the turbine operation mode had to be changed over into single valve mode again. The single valve operation mode causes larger cutoff loss, and the steam rate of the unit will increase, the economical efficiency of the unit will reduce. The open sequence of single valve mode and sequence valve mode was regulated, the unit vibration had been controlled less than 70μm, and the desired effects were obtained. 

Key words: single valve operation, vibration, reason analysis, open sequence of single valve mode and sequence valve mode

曾琦. 330MW汽轮机单多阀切换时轴承振动原因分析[J]. 华电技术, 2011, 33(2): 6-7.

ZENG Qi. Analysis on reasons of bearing vibration of 330MW steam turbine in changeover from single valve mode into sequence valve mode[J]. Huadian Technology, 2011, 33(2): 6-7.

[1]	程学庆,施佳赟. 某核电站主给水前置泵振动超标治理[J]. 华电技术, 2020, 42(5): 83-88.
[2]	陈浩，徐军锋. 600MW超临界机组配汽特性对轴系振动的影响[J]. 华电技术, 2019, 41(9): 29-32.
[3]	陆定康，周伟. 工业水泵振动异常分析和处理[J]. 华电技术, 2019, 41(8): 78-80.
[4]	陈啸，徐威，刘利，陈鑫. 某600MW机组汽轮机异常振动的分析及处理[J]. 华电技术, 2019, 41(7): 64-66.
[5]	吴昌浩，曹景芳. 低速钢球磨煤机减速机齿轮断齿故障诊断及分析[J]. 华电技术, 2019, 41(5): 69-72.
[6]	周兴宏. GE PG9171E重型燃机轴振超限的原因及处理[J]. 华电技术, 2019, 41(5): 76-77.
[7]	冯坤. 1000 MW超超临界机组发电机调试期间振动问题的分析及处理[J]. 华电技术, 2019, 41(12): 41-45.
[8]	徐要伟1，朱晨1，张文科2. 水电站泄洪闸弧形工作闸门原型观测试验[J]. 华电技术, 2019, 41(12): 46-49.
[9]	刘强. 汽轮机安全监视系统设备存在的问题及防范措施[J]. 华电技术, 2018, 40(9): 30-31.
[10]	陈杰，赵卫正. 600MW机组通流改造后振动故障诊断及处理[J]. 华电技术, 2018, 40(9): 40-43.
[11]	王博磊，曹伟，牟法海，昃刚，巩振泉. 热电联产汽轮发电机组振动异常原因分析与处理[J]. 华电技术, 2018, 40(8): 42-43.
[12]	汪小峰1，陈锐2. 某电厂主蒸汽管道振动原因分析及治理[J]. 华电技术, 2018, 40(7): 32-34.
[13]	安宗武1，孟颖琪1，刘超1，李长海1，吴忠胜2. 新型350MW超临界供热机组调试期间故障分析及处理[J]. 华电技术, 2018, 40(7): 50-53.
[14]	孙海元. 某电厂330MW汽轮机冷态启动用时过长原因分析及处理[J]. 华电技术, 2018, 40(7): 54-55.
[15]	卜峥嵘1，程勇明2，安付立2，刘宾2. 高温高压蒸汽管道振动分析治理[J]. 华电技术, 2018, 40(5): 41-44.