汽轮机调节系统卡涩原因分析及处理措施

华电技术 ›› 2015, Vol. 37 ›› Issue (3): 66-67.

汽轮机调节系统卡涩原因分析及处理措施

(北京仟亿达科技股份有限公司，北京〓100022)

出版日期:2015-03-25 发布日期:2015-05-14

Analysis on reasons of jam fault of steam turbine governing system and treatment measures

(Beijing Kingeta Technology Corporation Limited, Beijing 100022, China)

Online:2015-03-25 Published:2015-05-14

摘要/Abstract

摘要： 摘要：针对汽轮机调节系统出现的迟缓、卡涩等问题进行了分析，确认是前轴承座角销(压板)及回油管存在缺陷，在机组启动过程中引导前轴承座向左前方偏移，造成转子偏心使前汽封右侧漏汽量增大，导致调节汽门杠杆、支架等受热膨胀不均。对滑销系统进行调整，排除了设备隐患，保证了机组正常运行。

关键词: 关键词：汽轮机, 调节系统, 角销, 回油管, 轴承座, 汽封

Abstract: Abstract:Some problems, such as sluggish and jam, occurred in the steam turbine governing system. The problems were analyzed, and it was confirmed that there were defects in the front bearing seat angular pin (plate) and the oil return pipe. In unit startup process, the defects can lead the front bearing seat to shift to left front direction, which will cause the rotor to be offcenter, the steam leakage in front steam seal right side to increase, and the heating expansion of the lever and support of the governing valve to be uneven. The sliding key system was adjusted, the equipment hidden danger was eliminated, and the normal operation of the unit was ensured.

Key words: Keywords:steam turbine, governing system, angular pin, oil return pipe, bearing seat, steam seal

丁怀高. 汽轮机调节系统卡涩原因分析及处理措施[J]. 华电技术, 2015, 37(3): 66-67.

DING Huaigao. Analysis on reasons of jam fault of steam turbine governing system and treatment measures[J]. Huadian Technology, 2015, 37(3): 66-67.

[1]	周兴宏. GE PG9171E重型燃机轴振超限的原因及处理[J]. 华电技术, 2019, 41(5): 76-77.
[2]	方建勇. 某汽轮机盘车装置损坏原因分析及改进措施[J]. 华电技术, 2017, 39(1): 53-55.
[3]	刘金秋，夏晓涛，冯翌轩，尚伟. 汽轮机叶片叶身及围带的涡流检测[J]. 华电技术, 2016, 38(9): 36-37.
[4]	刘成柱. 基于日立系统的东汽机组PLU设计原理分析及调试方法[J]. 华电技术, 2016, 38(9): 46-47.
[5]	杨占岗. TC2F汽轮机交流油泵电机过电流故障原因分析[J]. 华电技术, 2016, 38(8): 40-41.
[6]	彭博伟. 660MW机组热应力控制策略的特点及应用分析[J]. 华电技术, 2016, 38(8): 51-53.
[7]	黄小军. 600MW汽轮机的优化启动[J]. 华电技术, 2016, 38(7): 20-24.
[8]	高强生1，赵苏平2. 300MW汽轮机低压转子叶片腐蚀原因分析及对策[J]. 华电技术, 2016, 38(7): 43-46.
[9]	李绍刚，韩丽娜. 一起汽轮机A变压器跳闸事故原因分析及处理[J]. 华电技术, 2016, 38(6): 41-42.
[10]	马保会. 降低汽流激振的阀序调整方法[J]. 华电技术, 2016, 38(4): 43-44.
[11]	施正生，童熙，欧锁实，季建宇，印广. 汽缸垂弧对汽封间隙调整的影响及对策[J]. 华电技术, 2016, 38(3): 26-28.
[12]	郭伯春1，肖胜2. 汽轮机阀门状态诊断系统设计与实现[J]. 华电技术, 2016, 38(3): 38-40.
[13]	柯昭. DEH一次调频在实际应用中存在的问题[J]. 华电技术, 2016, 38(3): 44-47.
[14]	陶力威. 680 MW 机组增压风机动叶自动调节系统改进[J]. 华电技术, 2015, 37(9): 42-43.
[15]	陈远东. 汽轮机部分进汽调节级三维流场数值研究[J]. 华电技术, 2015, 37(8): 1-5.