The method of shafts alignment of a turbogenerator set

Huadian Technology ›› 2011, Vol. 33 ›› Issue (3): 20-23.

• 研究与开发 • Previous Articles Next Articles

The method of shafts alignment of a turbogenerator set

HUANG Guoqiang

Sichuan Power Construction Second Company，Chengdu 610051, China

Received:1900-01-01 Revised:1900-01-01 Published:2011-03-25

Abstract

Abstract: Shafts alignment is the most important procedure in a turbogenerator set installation, which is related with the safety, stability and operation economy of units. The right method and procedure for aligning the shafts of turbogenerator set are the key guarantee to successfully install. This paper introduced the correlation method and procedure for shafts alignment, and the relating matters needed to pay attention were pointed out.

Key words: high-capacity unit, high-parameter unit, alignment, procedure, matters need attention

HUANG Guoqiang. The method of shafts alignment of a turbogenerator set[J]. Huadian Technology, 2011, 33(3): 20-23.

[1]	GONG Gangjun, MENG Zhiruo, TIAN Huiwen, LIU Ren, JIN Lu. Evolution analysis on security program requirements for operation and maintenance service providers in IEC 62443 [J]. Huadian Technology, 2021, 43(2): 77-82.
[2]	MAO Yangjun. Model selection and installation of coupling for the LM series aeroderivative gas turbine generator [J]. Huadian Technology, 2019, 41(8): 15-19.
[3]	TIAN Xiaobing，ZHANG Yi. Common fault treatment and optimization of oil pressure device [J]. Huadian Technology, 2018, 40(6): 41-43.
[4]	LIU Kaihui, LIU Liwei, NIE Haitao. Flue gas wet type desulfurization gypsum dewater system improvement and implementation [J]. Huadian Technology, 2017, 39(7): 64-66.
[5]	ZHANG Bo. Importance of three machines and one support five clean and five inspect importance brief analysis [J]. Huadian Technology, 2017, 39(11): 73-74.
[6]	ZHANG Junxing. Hydraulic support top beam collisionprotection device reproduce improvement [J]. Huadian Technology, 2017, 39(11): 63-64.
[7]	WANG Haibo. The Construction and implementation of centralized control evaluation system for the power plant [J]. Huadian Technology, 2014, 36(5): 8-10.
[8]	GONG Likui. Protection configuration and way of program trip shut down in the protection for the large generatortranformer set [J]. Huadian Technology, 2012, 34(8): 60-62.
[9]	LIU Hainan. Analysis on reason of larger vibration of belt conveyor driving device and treatment [J]. Huadian Technology, 2011, 33(11): 65-66.
[10]	CUI Chuantao. Calculation method of alignment for shaft system of turbogenerator set [J]. Huadian Technology, 2011, 33(1): 27-30.
[11]	CHEN Qiyin;JIANG Yinong. New alignment method for minor axis connected Coupling [J]. Huadian Technology, 2010, 32(9): 49-51.
[12]	LI Yuzhu;YU Hua. Welding procedure of submerged automatic arc welding for large cylinder shell [J]. Huadian Technology, 2010, 32(4): 42-44.
[13]	HAN Jun. Safeguard measures of installation quality for air cooling system [J]. Huadian Technology, 2009, 31(3): 56-58.

The method of shafts alignment of a turbogenerator set

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 13

Recommended Articles

Metrics

Comments